Cat8 Ethernet Patch Cable RJ45-RJ45 UTP STP/FTP,SFTP and SSTP

1000BASE-ZX SFP 1550nm 80km DOM LC SMF Transceiver Module is designed for use in 100GBASE Ethernet and 4x28G OTN client interfaces throughput up to 80km over single mode fiber(SMF) using a wavelength of 1550nm via duplex LC connectors. Taking BOX+FPC+PCBA separate design, it has great reliability, airtightness and heat dissipation performance. This transceiver is compliant with IEEE 802.3ba 100GBASE-LR4 and OTU4 4I1-9D1F standard. Digital diagnostics functions are also available via the I2C interface, as specified by the QSFP28 MSA, to allow access to real-time operating parameters. With these features, this easy to install, hot swappable transceiver is suitable to be used in various applications, such as 100G Ethernet, 112G OTN OTU4, telecom, service provider applications and 5G wireless network.

The LC fiber loopback is used to test the signal backhaul in the system or network system. Through the backhaul signal, various potential anomalies in the network link can be detected. This type of detection is commonly used to ensure the network link..

4/8/16/32/64/128 Core PLC splitter distribution box is used as a termination point for the feeder cable to connect with optical splitter in FTTx communication network system. The fiber splicing, splitting, distribution can be done in this box, and meanwhile it provides solid protection and management for the FTTx network building.

Armored fiber optic cable consists of a cable surrounded by a stainless steel tube to protect it from moisture and abrasion. Such armored cable can be much stronger than regular indoor cable due to its high tensile force.SZOPT offers both singlemode and multimode armored cable with outer sheath of yellow,blue,beige or custom.

Variable in-line optical attenuators,also know as adjustable in-line optical attenuator or short as VOA, are used to permit dynamic control of optical power levels in a fiber. It can be applied to adjust power level of signal in the optical communication at the output of light sources, E/O converters and for the linear or dynamic range of power meter. Furthermore, they can the used in optical amplifier systems to balance the gain across the different operating wavelengths.

FC/UPC Fast Connector,also known as Field installation connector FC/UPC,or Fast assembly connector FC/UPC, is a new kind of connector that can be used in FTTH project scene. They don’t need polishing, no epoxy. They could be installed in the field and make connection less than two minutes. Furthermore, it doesn’t need the fused fiber. Only need some simple tools,by this way,it can save time and cost.SZOPT can offer you different models for options,please reach us for details.

ODF is the short term of Optical Distribution Frame, is a high-density, large-capacity design box with cold rolled steel sheet, reasonable distribution, easy to manage, install and operate.

This is a kind of ABS box PLC Splitter available with 1X4/1X8/1X16/1X32/1X64/1X128,2X4/2X8/2X16/2X32/2X64/2X128,the terminators can be  sc/lc/fc/st in 3.0mm or 2.0mm cable,the cable length is usually 1-1.5m.Available wavelength is:1260-1650nm.

Adapter type fixed attenuator is the female to female fixed fiber optic attenuator,whichutilizes the air gap between two connectors to achieve the optical attenuation. Fixed adapter type attenuator is simple, low-cost and compact. It is recommended for use where return loss is not a concern nor is absolute attenuation value.

SZOPT offers a full range of CWDM&DWDM to meet the demand of applications such as: Gigabit & 10G Ethernet,SDH/SONET,ATM,ESCON,Fibre Channel,FTTx and CATV,etc.

Fiber Adapters (Mating Sleeve Fiber Adapter or Standard Fiber Adapter or Bulkhead Type Fiber Adapter) also called fiber adaptors,are used to link optical cables or device. Usually they are female to female,or female to male. SZOPT’s fiber adapters are mainly with ceramic sleeves, but phosphor bronze sleeve is an option for some special requirement.

Variable in-line optical attenuators,also know as adjustable in-line optical attenuator or short as VOA, are used to permit dynamic control of optical power levels in a fiber. It can be applied to adjust power level of signal in the optical communication at the output of light sources, E/O converters and for the linear or dynamic range of power meter. Furthermore, they can the used in optical amplifier systems to balance the gain across the different operating wavelengths.