Cat5 Cat6 Cat7 Cat8 UTP FTP SFTP Patch Cord

Fiber Optic Attenuator is one kind of optical passive device which is used to debug the performance of the optical power in the optical communication system,debugging fiber optic instrument calibration correction, optical signal attenuation.And used for the attenuation of the input optical power, avoid optical receiver distortion due to input optical power powerful. The fixed fiber optic attenuator can achieve the dual function of adapter and attenuators.

Fiber Adapters (Mating Sleeve Fiber Adapter or Standard Fiber Adapter or Bulkhead Type Fiber Adapter) also called fiber adaptors,are used to link optical cables or device. Usually they are female to female,or female to male. SZOPT’s fiber adapters are mainly with ceramic sleeves, but phosphor bronze sleeve is an option for some special requirement.

SZOPT’s passive copper cable solutions provide power-efficient replacement for active power connectivity such as fiber optic cables. The SFP SFP+ QSFP+ QSFP28 cables provide 1Gb 40Gb 100Gb systems the ability to connect to switches or adapter cards. Optimizing systems to operate with passive copper cables significantly reduce power consumption and enlarge the connectivity opportunities of the system.

PLC (Planar Lightwave Circuit) splitter is based on planar lightwave circuit technology and provides a low cost light distribution solution with small form factor and high reliability.SZOPT provides a various types of 1×N and 2×N PLC splitters, including 1×2/4/8/16/32/64,2×2/4/8/16/32/64 etc.PLC splitters. All of our products are all with superior optical performance, high stability and high reliability to meet various application requirement.

1000BASE-ZXC SFP 1550nm 160km DOM LC SMF Transceiver is designed for use in 100GBASE Ethernet and 4x28G OTN client interfaces throughput up to 160km over single mode fiber(SMF) using a wavelength of 1550nm via duplex LC connectors. Taking BOX+FPC+PCBA separate design, it has great reliability, airtightness and heat dissipation performance. This transceiver is compliant with IEEE 802.3ba 100GBASE-LR4 and OTU4 4I1-9D1F standard. Digital diagnostics functions are also available via the I2C interface, as specified by the QSFP28 MSA, to allow access to real-time operating parameters. With these features, this easy to install, hot swappable transceiver is suitable to be used in various applications, such as 100G Ethernet, 112G OTN OTU4, telecom, service provider applications and 5G wireless network.

SZOPT’s SC/APC OptiTap connector cable assemblies provide a cost effective, convenient operation, environmental seal and mechanical protection solution. The design makes the connector has blind-mating function, provides quick installation solutions and has good performance, it can be compatible with all the similar products in market, such as Corning Opitap-SC and H-type connector, Cable can be 2×3.0mm, 2×5.0mm flat drop or 5.0mm and 7.0mm round cable, amored or non-amored. Please reach us for details.

SZOPT offers a full range of CWDM&DWDM to meet the demand of applications such as: Gigabit & 10G Ethernet,SDH/SONET,ATM,ESCON,Fibre Channel,FTTx and CATV,etc.

This is a kind of stainless steel tube mini module PLC Splitter 1:16 with sc/lc/fc/st in 0.9mm cable,the cable length is usually 1-1.5m.Available wavelength is:1260-1650nm.

GYTS/GYTA cable is a type of the outdoor cable used for duct and direct buried applications with corrugated steel tape or aluminum tape. SZOPT supplies both single mode and multimode GYTS cables.PBT loose tube has 2-12 fibers, The central Strength member is: steel wire. It has a Filling Compound; Longitudinal corrugated steel tape laminated with polyethylene on both sides. Consequently.

Fiber Adapters (Mating Sleeve Fiber Adapter or Standard Fiber Adapter or Bulkhead Type Fiber Adapter) also called fiber adaptors,are used to link optical cables or device. Usually they are female to female,or female to male. SZOPT’s fiber adapters are mainly with ceramic sleeves, but phosphor bronze sleeve is an option for some special requirement.

MPO/MTP Fiber Optic Patch Panel is used for trunk cable connection and distribution cable management in distribution area of MDA, IDA or HDA data centers. It could be installed in 19 inch racks and cabinets. It could accommodate MPO/MTP cassette modules or MPO/MTP adapter panels.

Mode conditioning patch cords are required when Gigabit 1000BASE-LX routers and switches are installed into existing multimode cable plants. They are used to adapt the singlemode output of Gigabit Ethernet (1000BASE-LX) transceivers to a multimode cable network. All SZOPT’s mode-conditioning patch cords are fully compliant with IEEE 802.3z application standards.